Legacy Dell PowerEdge LCD Error Codes: Complete Source Table
This translates the stored historical Dell LCD-code table. The corresponding English PowerEdge R710 Hardware Owner’s Manual, Table 1-1, was located. These legacy E/I/W codes are not a complete message registry for every PowerEdge generation. Match the exact model and firmware; newer event codes and procedures differ.
The table preserves all 75 source message variants across 72 codes. Slot-specific variants share their parent code explicitly. References such as Getting Help or Troubleshooting System Memory refer to the matching system manual, not a generic procedure on this page.
Record/export the SEL and relevant hardware context before clearing a log. AC removal, restarts, reseating and replacements below describe source service actions that can interrupt workloads; carry them out only through the actual system’s service procedure. The source’s ten-second AC wait is retained for its legacy context. A cleared alert does not prove that the underlying fault is fixed.
| Code | LCD text from the source | Cause described by the source | Source corrective action |
|---|---|---|---|
| E1000 | Failsafe voltage error. Contact support. | View the System Event Log for critical fault events. | Disconnect the system AC power for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E1114 | Ambient Temp exceeds allowed range. | The ambient temperature has reached a point exceeding the permitted range. | See "System Cooling Problem Troubleshooting". |
| E1116 | Memory disabled, temp above range. Power cycle AC. | Memory temperature has exceeded the permitted limit; the system has disabled it to prevent component damage. | Disconnect the system AC power for 10 seconds, then restart the system. See "System Cooling Problem Troubleshooting". If the problem persists, see "Get Help". |
| E1210 | Motherboard battery failure.Check battery. | CMOS battery is missing or voltage is out of the permitted range. | See "System Battery Troubleshooting". |
| E1211 | RAID Controller battery failure.Check battery. | RAID battery is missing, damaged, or cannot be recharged due to temperature issues. | Reinsert the RAID battery connector. See "Installing RAID Battery" and "System Cooling Problem Troubleshooting". |
| E1216 | 3.3V Regulator failure. Reseat PCIe cards. | 3.3V regulator has failed. | Remove and reseat the PCIe expansion card. If the problem persists, see "Expansion Card Troubleshooting". |
| E1229 | CPU # VCORE Regulator failure.Reseat CPU. | A specific processor VCORE regulator has failed. | Reseat the processor. See "Processor Troubleshooting".If the problem persists, see "Get Help". |
| E122A | CPU # VTT Regulator failure.Reseat CPU. | A specific processor VTT regulator has failed. | Reseat the processor. See "Processor Troubleshooting".If the problem persists, see "Get Help". |
| E122C | CPU Power Fault. Power cycle AC. | A power fault was detected when applying power to the processor. | Disconnect the system AC power for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E122D | Memory Regulator # Failed. Reseat DIMMs. | A memory regulator has failed. | Reseat the memory modules. See "System Memory Troubleshooting". |
| E122E | On-board regulator failed. Call support. | An on-board regulator has failed. | Disconnect the system AC power for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E1310 | Fan ## RPM exceeding range. Check fan. | The RPM of a specific fan is outside the expected operating range. | See "System Cooling Troubleshooting". |
| E1311 | Fan module ## RPM exceeding range. Check fan. | The RPM of a specific fan in a specific module is outside the expected operating range. | See "System Cooling Troubleshooting". |
| E1313 | Fan redundancy lost. Check fans. | Fans in the system no longer have redundancy. If another fan fails, the system will be at risk of overheating. | Check the LCD for other scrolling information. See "Fan Troubleshooting". |
| E1410 | System Fatal Error detected. | A critical system error has been detected. | Check the LCD for other scrolling information. Disconnect the system AC power for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E1414 | CPU # temp exceeding range. Check CPU heatsink. | A specific processor has exceeded its acceptable temperature range. | Ensure the processor heatsink is properly installed. See "Processor Troubleshooting" and "System Cooling Troubleshooting". |
| E1418 | CPU # not detected. Check CPU is seated properly. | The specified processor is missing or damaged; the system configuration is not supported. | Ensure the specified processor is properly installed. See "Processor Troubleshooting". |
| E141C | Unsupported CPU configuration.Check CPU or BIOS revision. | The processor configuration is not supported. | Match the processors and their configuration to the supported specifications in the exact system Getting Started Guide. |
| E141F | CPU # protocol error. Power cycle AC. | The system BIOS reported a processor protocol error. | Disconnect system AC power for 10 seconds, then restart. If the problem persists, see Getting Help in the system manual. |
| E1420 | CPU Bus parity error. Power cycle AC. | The system BIOS reported a processor bus parity error. | Disconnect system AC power for 10 seconds, then restart. If the problem persists, see Getting Help in the system manual. |
| E1422 | CPU # machine check error. Power cycle AC. | The system BIOS has reported a machine check error. | Disconnect the AC power from the system for 10 seconds, then restart the system. If the problem persists, see "Getting Help". |
| E1610 | Power Supply # (### W) missing.Check power supply. | A specific power supply has been removed, or the system is missing this device. | See "Troubleshooting Power Supplies". |
| E1614 | Power Supply # (### W) error.Check power supply. | A specific power supply has failed. | See "Troubleshooting Power Supplies". |
| E1618 | Predictive failure on Power Supply # (### W). Check PSU. | A warning of an impending power supply failure has been issued due to a power supply fan failure, overheating, or a power supply communication error. | See "Troubleshooting Power Supplies". |
| E161C | Power Supply # (### W) lost AC power. Check PSU cables. | A specific power supply has been connected to the system, but there is no AC power input. | Check the AC power for the specified power supply. If the problem persists, see "Troubleshooting Power Supplies". |
| E1620 | Power Supply # (### W) AC power error. Check PSU cables. | The AC power input for a specific power supply is out of specification. | Check the AC power for the specified power supply. If the problem persists, see "Troubleshooting Power Supplies". |
| E1624 | Lost power supply redundancy.Check PSU cables. | The power supply subsystem no longer provides redundancy. If other power supplies fail, the system will shut down. | See "Troubleshooting Power Supplies". |
| E1626 | Power Supply Mismatch. PSU1 = ### W, PSU2 = ### W. | The power supplies in the system have different wattages. | Ensure that power supplies with matching wattage are installed. See the technical specifications listed in the "Getting Started Guide" system. |
| E1629 | Power required > PSU wattage.Check PSU and config. | The system configuration requires more power than the power supplies can provide, even with throttling enabled. | Turn off the system power, reduce the hardware configuration, or install higher-wattage power supplies, then restart the system. |
| E1710 | I/O channel check error. Review & clear SEL. | The system BIOS has reported an I/O channel check. | Review the details in the System Event Log (SEL), then clear the SEL. Disconnect the AC power from the system for 10 seconds, then restart the system. If the problem persists, see "Getting Help". |
| E1711 | PCI parity error on Bus ## Device ## Function ## | The system BIOS has reported a PCI parity error on a component located in the PCI configuration space at Bus ## Device ## Function ##. | Remove and reseat the PCIe expansion card. If the problem persists, see "Expansion Card Troubleshooting". |
| E1711 | PCI parity error on Slot #.Review & clear SEL. | The system BIOS has reported a PCI parity error on a component located in the specified slot. | Remove and reseat the PCIe expansion card. If the problem persists, see "Expansion Card Troubleshooting". |
| E1712 | PCI system error on Bus ## Device ## Function ## | The system BIOS has reported a PCI system error on a component located in the PCI configuration space at bus ##, device ##, function ##. | Remove and reseat the PCIe expansion card. If the problem persists, see "Expansion Card Troubleshooting". |
| E1712 | PCI system error on Slot #.Review & clear SEL. | The system BIOS has reported a PCI system error on a component located in the specified slot. | Reseat the riser card. See "Expansion Cards and Riser Cards". If the problem persists, the riser card or system board may be faulty. See "Get Help". |
| E1714 | Unknown error. Review & clear SEL. | The system BIOS has detected an error in the system but cannot determine its source. | Review the details in the System Event Log (SEL) and then clear the SEL. Disconnect the AC power from the system for 10 seconds and then restart the system. If the problem persists, see "Get Help". |
| E1715 | Fatal I/O Error | The system BIOS has determined that a fatal error exists in the system. | Review the SEL for details and then clear the SEL. Disconnect the AC power from the system for 10 seconds and then restart the system. If the problem persists, see "Get Help". |
| E1716 | Chipset IERR Bus ## Dev ##Function ##. Review & clear SEL. | The system BIOS has reported a chipset internal error residing in bus ##, device ##, function ##. | Review the SEL for details and then clear the SEL. Disconnect the AC power from the system for 10 seconds and then restart the system. If the problem persists, see "Get Help". |
| E1717 | CPU # internal error. Review & clear SEL. | The system BIOS has determined that an internal error has occurred on the specified processor. | Review the SEL for details and then clear the SEL. Disconnect the AC power from the system for 10 seconds and then restart the system. If the problem persists, see "Get Help". |
| E171F | PCIe fatal error on Bus ## Device ## Function ## | The system BIOS has reported a PCIe fatal error on a component located in the PCI configuration space at bus ##, device ##, function ##. | Remove and reseat the PCIe expansion card. If the problem persists, see "Expansion Card Troubleshooting". |
| E171F | PCIe fatal error on Slot #.Review & clear SEL. | The system BIOS has reported a PCIe fatal error on a component located in the specified slot. | Reseat the riser card. See "Expansion Cards and Riser Cards". If the problem persists, the riser card or system board may be faulty. See "Get Help". |
| E1810 | Hard drive ## fault. Review & clear SEL. | A specified hard disk drive has failed. | See "Hard Drive Troubleshooting". |
| E1812 | Hard drive ## removed. Check drive. | A specified hard disk drive has been removed from the system. | For reference only. |
| E1A11 | PCI Riser hardware & configuration mismatch. Reconfigure. | The PCIe riser is configured incorrectly. Some invalid configurations will prevent the system from powering on. | Reseat the expansion card riser. See "Expansion Cards and Riser Cards".If the problem persists, the riser card or system board may be faulty. See "Get Help". |
| E1A12 | PCI Riser not detected. Check Riser. | One or two PCIe risers are missing. This will prevent the system from booting. | Reinstall the missing riser card. See "Reinstalling Riser Card 1" and "Reinstalling Riser Card 2". |
| E1A14 | SAS cable A failure. Check connection. | SAS cable A is missing or damaged. | Reseat the cable. If the problem persists, replace the cable.If the problem persists, see "Getting Help". |
| E1A15 | SAS cable B failure. Check connection. | SAS cable B is missing or damaged. | Reseat the cable. If the problem persists, replace the cable.If the problem persists, see "Getting Help". |
| E1A1D | Control panel USB cable not detected. Check cable. | The USB cable connected to the control panel is missing or damaged. | Reseat the cable. If the problem persists, replace the cable.If the problem persists, see "Getting Help". |
| E2010 | Memory not detected. Inspect DIMMs. | Memory was not detected in the system. | Install memory or reseat memory modules. See "Installing Memory Modules" or "Troubleshooting System Memory". |
| E2011 | Memory configuration failure.Check DIMMs. | Memory was detected, but it could not be configured. An error was detected during memory configuration. | See "Troubleshooting System Memory". |
| E2012 | Memory configured but unusable.Check DIMMs. | Memory is configured but unavailable. | See "Troubleshooting System Memory". |
| E2013 | BIOS unable to shadow memory.Check DIMMs. | The system BIOS cannot copy its flash image into memory. | See "Troubleshooting System Memory". |
| E2014 | CMOS RAM failure. Power cycle AC. | CMOS has failed. CMOS RAM is not functioning properly. | Disconnect the AC power from the system for 10 seconds, then restart the system. If the problem persists, see "Getting Help". |
| E2015 | DMA Controller failure. Power cycle AC. | The DMA controller has failed. | Disconnect the AC power from the system for 10 seconds, then restart the system. If the problem persists, see "Getting Help". |
| E2016 | Interrupt Controller failure.Power cycle AC. | The interrupt controller has failed. | Disconnect the AC power from the system for 10 seconds, then restart the system. If the problem persists, see "Getting Help". |
| E2017 | Timer refresh failure. Power cycle AC. | Timer refresh failure. | Disconnect the AC power from the system for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E2018 | Programmable Timer error. Power cycle AC. | Programmable interval timer error. | Disconnect the system's AC power for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E2019 | Parity error. Power cycle AC. | Parity error. | Disconnect the system's AC power for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E201A | SuperIO failure. Power cycle AC. | SIO has failed. | Disconnect the system's AC power for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E201B | Keyboard Controller error. Power cycle AC. | Keyboard controller failure. | Disconnect the system's AC power for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E201C | SMI initialization failure. Power cycle AC. | System Management Interrupt (SMI) initialization failure. | Disconnect the system's AC power for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E201D | Shutdown test failure. Power cycle AC. | BIOS shutdown test failure. | Disconnect the system's AC power for 10 seconds, then restart the system. If the problem persists, see "Get Help". |
| E201E | POST memory test failure. Check DIMMs. | BIOS POST memory test failure. | See "System Memory Troubleshooting".If the problem persists, see "Get Help". |
| E2020 | CPU configuration failure. Check screen message. | Processor configuration failure. | Please view the specific error message on the screen. See "Processor Troubleshooting". |
| E2021 | Incorrect memory configuration.Review User Guide. | Memory configuration is incorrect. | Please view the specific error message on the screen. See "System Memory Troubleshooting". |
| E2022 | General failure during POST.Check screen message. | General failure after video. | Please view the specific error message on the screen. |
| E2023 | BIOS unable to mirror memory.Check DIMMs. | Due to a memory module failure or invalid memory configuration, the system BIOS cannot enable memory mirroring. | See "System Memory Troubleshooting". |
| E2110 | Multibit Error on DIMM ##. Reseat DIMM. | A Multibit Error (MBE) has occurred on the memory module in slot "##". | See "System Memory Troubleshooting". |
| E2111 | SBE log disabled on DIMM ##.Reseat DIMM. | The system BIOS has disabled Single Bit Error (SBE) logging for memory. No further SBEs will be logged until the system is rebooted. "##" represents the memory module indicated by the BIOS. | Disconnect the AC power from the system for 10 seconds, then restart the system. If the problem persists, see "System Memory Troubleshooting". |
| E2113 | Mem mirror OFF on DIMM ## & ##.Power cycle AC. | Memory mirroring has been disabled because the system BIOS determined that too many errors exist in half of the mirrored pair. "## and ##" represent the memory module pairs indicated by the BIOS. | Disconnect the AC power from the system for 10 seconds, then restart the system. If the problem persists, see "System Memory Troubleshooting". |
| I1910 | Intrusion detected. Check chassis cover. | The system cover has been removed. | For reference only. |
| I1911 | LCD Log Full. Check SEL to review all Errors. | LCD overflow message. The LCD can display a maximum of ten error messages sequentially. The eleventh message directs the user to check the SEL for event details. | Check the SEL for detailed event information.Disconnect the AC power from the system for 10 seconds, or clear the SEL. |
| I1912 | SEL full. Review & clear log. | The events recorded in the SEL are full, and no other events can be recorded. | Please review the details in the SEL and then clear the SEL. |
| W1228 | RAID Controller battery capacity < 24hr. | The source warns that the RAID controller battery has less than 24 hours of cache-backup capacity. | Follow the matching controller procedure to recharge and verify the battery backup capacity. If it remains insufficient, replace the approved RAID battery as described in the system manual. |
| W1627 | Power required > PSU wattage.Check PSU and config. | The system configuration requires more power than the power supply unit can provide. | Turn off the system power, reduce the hardware configuration, or install a higher-wattage power supply unit, then restart the system. |
| W1628 | Performance degraded. Check PSU and system configuration. | The system configuration requires more power than the power supply unit can provide, but the system can boot using throttling. | Turn off the system power, reduce the hardware configuration, or install a higher-wattage power supply unit, then restart the system. |
In W1228, “less than 24hr” concerns battery-backed cache retention capacity; it is not a statement that the server can run on that battery for 24 hours. Preserve controller cache data through the applicable replacement procedure.